A353

The SDA3051-100-M is a highly reliable amplifier.It employs ultra-wideband GaN transistors that can output 100 watts of power within the 30MHz to 512MHz frequency range while maintaining relevant RF performance.In contrast to traditional CW amplifiers,this amplifier can amplify spread-spectrum signals,with an instant bandwidth of up to 200 MHz. When paired with the appropriate SDR digital excitation source,it can produce excellent interference effects on remote control,data transmission,and positioning signals.Therefore,this amplifier is particularly suitable for use in wireless communication interference systems in the V and U bands,including but not limited to mobile phones,radiio stations,and drones.

Categories:

CPA

+86 18926758761

Tel

Amy@junteli.com

E-mail

Specification Sheet

Online inquiry

Product Details

Applicaton and Feature:

Utilizing third-generation GaN transistors
Ultra-wide working bandwidth and instant bandwidth
Excellent reliability
Features temperature detection,standing-wave detection,and protection functions
RS485 serial interface for monitoring and control [note1]

Electrical Speciﬁcations:

Parameter	Min	Typ	Max	Unit	Test Condition
Operating frequency	30		512	MHz
Instant bandwidth			200	MHz	Broadband signal,such as OFDM signal
Output power（Psat）	80	100		W	CW signal
Gain（small signal）	41		51	dB	Measured with VNA in swept frequency mode at -20dBm. Input power calibrated/measuredat the amplifier input port.
Gain flatness（small signal）	-4		4	dB	Test condition the same as Gain
Gain adjustment range[note1]	20			dB	Test condition the same as Gain
Input RF power range	0		8	dBm
Gain adjustment step size[note1]	0.5			dB	Test condition the same as Gain
Noise figure			20	dB
Input VSWR			1.8		Measured with VNA in sweptfrequency mode at -20dBm. Input power calibrated/measuredat the amplifier input port.
Spurious		-60		dBc	CW signal at the output power of 100W. Spurious defined as any non-harmonic amplifier outpur. Spurious measured in a 1kHz resolution bandwidth, 10kHz videobandwidth. Specifications apply atoffsets of greater than or equal to ±10kHz from the RF carrier. Maximum measurement frequency is 8GHz
Harmonics(2ⁿᵈ, 3ⁿᵈ)	-10			dBc	CW signal source at output power of 100W
Operating voltage	24	28	32	V	Note:Output power capabilities andgain will vary with voltage
Operating current		14.5	18	A	CW signal source at output power of 100W
PA Enable/Disable time			10	μs	Measurement with of 100W CW output. Rise and fall time of amplifier output envelope recorded. Rise andfall times at 10%-90% of the output power in linear scale. PA Enable/Disable signal set to 10kHz repetition rate and 50% duty cycle

Alarm and Protection:

Parameter	Introductions
Over temperature	When the temperature exceeds 80℃±5℃ , the amplifier PIN12 will outputs +5V voltage and the amplifier will automatically shut down; When the temperature drops below 70℃±5℃, the amplifier will automatically turn on.
Over VSWR	When the output port of the amplifier is open or short, the amplifier PIN13 will outputs +5V voltage and the amplifier shut down, the statuswill be locked . The alarm state will be cleared once pin 6 transmits a pulse signal
Over voltage[note1]	The amplifier PIN2 will outputs +5V voltage and the amplifier shutdown when the voltage exceeds 32V, the status will be locked. The alarm state will be cleared once pin 6 transmits a pulse signal
Over current[note1]	The amplifier PIN3 will outputs +5V voltage and the amplifier shutdown when the current exceeds 20A., the status will be locked. The alarm state will be cleared once pin 6 transmits a pulse signal

Environmental Specifications:

Parameter	Min	Typ	Max	Unit
Operating temperature	-40		+60	℃
Storage temperature	-55		+85	℃
Relative Humidity(non-condensing)			+95	%
Altitude	MIL-STD-810F Method 500.4
Vibration/Shock	Pass MIL-STD-810F - Method 514.5/516.5 – Proc I

Mechanical Specifications:

Parameter	Value	Unit
Dimension	160 x 120 x 25	mm
Weight	1.4	kg
RF Connectors In/Out	Input: SMA-F Output: N-F	-
Control Connector	D-Sub 15-Pin Female	-
Power Supply Connector	Pull-core Capacitance	-
Cooling	External Heat sink	-

DC Interface Connector:

PIN#	Description	Specification
Grounding Post	GND	Ground Return
Pull-coreCapacitance	VDD	Supply Voltage:+24V~32V,+28V Nominal
1	RS485 (-)[note1] [note2]	Serial Communication Bus
2	Voltage Alarm[note1]	Alarm(5V), the amplifier shut down when the voltage exceeds 32V, the status will be locked.
3	Current Alarm[note1]	Alarm(5V), the amplifier shut down when the current exceeds 20A., the status will be locked.
5	Attenuator setting[note1]	Voltage input in the range of 0.5-3.0VDC, 0.5VDC corresponds with minimum attenuation, 3.0VDC is maximum attenuation.
6	Alarm Reset	If the alarm has been triggered,input an extermal pulse singalto reset it (0V ~ 0.7V is the low level, 3.3V ~ 5V is the highlevel)
7	Pr	Reversed RF Power Indicator (0~3V)
8	RS485 (+)[note1] [note2]	Serial Communication Bus
10	Pf	Forward RF Power Indicator (0~3V)
11	PA EN	PA on :0V ~ 0.7V or the HandingPA off :Inout 3.3V ~ 5V
12	TA	Alarm(5V), when the temperature exceeds 80℃±5℃ and the amplifier shutdown
13	VA	Alarm(5V), When the output port of the amplifier is open or short, the amplifier will shutdown.
14	Tc	Analog voltage relative to Unit’s Temperature @ 10mV/℃(0.50Voffset); (Vmeausred-0.50)/0.01=X℃,Example: (1.00V-0.50)/0.01= 50℃
4,9,15	NC

[note1]：This function is optional, and the optional model number is SDA3051-100-M1.
[note2]：This function is optional, and the optional model number is SDA3051-100-M1.
The RS485 master-slave communication function can be used to monitor the operational parameters of the power amplifier module, such as voltage, current, output power, and standing wave, and it can also be used to set the control parameters of the power amplifier in real time, such as power amplifier on/off, gain adjustment, power adjustment, and alarm reset.

Outline Drawing: